New Trucks For Sale with Bucket Trucks Near southmayd, Arkansas

<p><strong>Minimum Chassis Requirements:</strong><br>• Clean Cab to Axle Dimension (tops, sides and bottoms) …………………………………………………….. 60 in. (1.52 m)<br>• Frame Section Modulus …………………………………………………………………………………………….. 9.25 in3 (152 cm3)<br>• Frame Resisting Bending Moment ……………………………………………………………….. 333,000 in-lbs. (37,600 N-m)<br>• GVWR ………………………………………………………………………………………………………………… 17,500 lbs. (7935 kg)<br>• Front GAWR ………………………………………………………………………………………………………….. 6,000 lbs. (2722 kg)<br>• Rear GAWR ………………………………………………………………………………………………………… 13,500 lbs. (6124 kg)<br>• Approximate Curb Weight for Stability …………………………………………………………………….. 13,100 lbs. (5942 kg)<br>• PTO Provision<br>• Rear Fuel Tank Only<br>• 2024 Ford F-550<br>• Diesel Engine<br>• Dash Mounted PTO and Upfitter Switches<br>• Factory Back-up Camera</p><p><strong>BODY SPECIFICATIONS</strong><br>Brand FX Bodies 132” long x 42” high x 94” wide service body including the following:<br>• 30 inch aluminum tread plate platform extension<br>• BFX LED lighting package installed in tail shelf.<br>• Cable access step at rear and side access.<br>• Two (2) stainless steel grab handles at side access and two (2) aluminum grab rails at rear tail shelf.<br>• Wheel chock storage and outrigger pad holders.<br>• Push/pull rod lock system<br>o 42” High Street side compartments as follows<br>• 1st Vertical: Two (2) adjustable shelves with dividers<br>• 2nd Vertical: Two (2) adjustable shelves with dividers<br>• Horizontal: One (1) removable shelf with dividers • Rear Vertical: Two (2) adjustable shelves with dividers • Hot stick shelf with rear access door.<br>o 42” High Curbside compartments as follows<br>• 1st Vertical: Two (2) adjustable shelves with dividers and cutout for outrigger • 2nd Vertical: Grip strut access steps to bed area with removable plastic tail board.<br>• Horizontal: One (1) adjustable shelf with dividers<br>• Rear Vertical: Five (5) fixed material hooks 1-3-1</p>

<p><strong>Minimum Chassis Requirements:</strong></p><ul><li>Clean Cab to Axle Dimension (tops, sides & bottoms) ………………………………………………………. 84 in. (2.14 m)</li><li>Frame Resisting Bending Moment ……………………………………………………………… 530,000 in-lbs. (60,000 N-m)</li><li>GVWR ………………………………………………………………………………………………………………. 19,500 lbs.</li></ul><p>(8845 kg)</p><ul><li>• Front GAWR ………………………………………………………………………………………………………… 7,000 lbs.</li></ul><p>(3175 kg)</p><ul><li>• Rear GAWR ………………………………………………………………………………………………………. 13,500 lbs.</li></ul><p>(6120 kg)</p><ul><li>Approximate Curb Weight for Stability …………………………………………………………………… 14,500 lbs. (6580 kg)</li><li>PTO Provision</li><li>Rear Fuel Tank Only</li><li>Trailer brake controller</li><li>Rear view camera and prep kit</li><li>Ford F-550 4×4</li><li>Diesel Engine</li></ul><p><strong>BODY SPECIFICATIONS </strong> <strong>Steel Service Body:</strong></p><p>132″ Service Body 40 inches high X 94 inches wide.</p><p><strong>Body Dimensions:</strong></p><ul><li>20 Inch compartment depth.</li><li>54 Inch bed area.</li><li>24 Inch top of floor to top of body.</li><li>18 Inch horizontal compartment height.</li></ul><p><strong>Body Materials:</strong></p><ul><li>16 Ga. Galvanneal body materials.</li><li>12 Ga. Hot rolled treadplate floor.</li><li>12 Ga. Hot rolled treadplate compartment tops.</li></ul><p><strong>Door Details:</strong></p><ul><li>Stainless Steel Automotive rotary type door latches</li><li>Latch Covers on All doors.</li></ul><p>VO-40-MHI VSW-23390 VERSALIFT.COM</p><p><strong>BODY SPECIFICATIONS (Continued)</strong></p><ul><li>Stainless steel rod and socket type door hinges.</li><li>Chain stops on all doors.</li><li>18 Ga. Double Panel Body Doors.</li></ul><p><strong>Body Features:</strong></p><ul><li>Rubber rolled crown type fenders.</li><li>Master door lock system.</li><li>Automotive Bulb Type Weatherstripping.</li><li>Front bulkhead.</li><li>Shelving / Hooks installed on DUAL Uni-Strut for infinite adjustment.</li><li>Two (2) formed angle Mudflap brackets</li></ul>

2022 Freightliner M2106, ,FOR SALE! A brand new Freightliner M2106 6x6 upfitted with a Terex TL80-112 bucket. This vehicle is powered by a 350 hp Cummins L9 diesel motor, and gears are shifted via an Allison 3000RDS automatic transmission. The FAWR is 18k lbs and the rear is rated at 40k lbs. The upfitted TL80-112 offers a max working height of 112 ft, and a max side reach of 63.3 ft. Contact for more information!

2022 Peterbilt 220 EV, ,FOR SALE! A brand new Peterbilt 220 EV 4x2 upfitted with a Versalift VST-52-MHI bucket. This vehicle is powered by a 347 hp Dana TM4 HDHV3500 electric engine, and gears are shifted via a midship electric transmission. The FAWR is 12k lbs and the rear is rated at 21k lbs. The upfitted Versalift VST-52-MHI offers a working height of 56.5 ft and a horizontal reach of 30.33 ft. The platform is rated at 400 lbs. Contact for more information!

<ul><li>106″ BBC Flat Roof Cab</li><li>Conventional, Aluminum</li><li>Fiberglass Hood</li><li>Single 14″ Round Hadley Air</li><li>Horn</li><li>Dual Electric Horns</li><li>(51 Amber Marker Lights</li><li>Daytime Running Lights</li><li>Dual West Coast Heated Mirrors</li><li>Bright Finish</li><li>Opal Gray Vinyl Interior</li></ul> <ul><li>Interior Convenience Package</li><li>Heater, Defroster, A.C.</li><li>Hi-Back Air Ride Driver Seat</li><li>Hi-Back Rider Seat</li><li>11] 12V Power Supply In-Dash</li><li>Adjustable Tilt/Tele. Steering</li><li>Column</li><li>97 DB Backup Alarm</li><li>AM/FM/WB Radio w/ Front Aux</li><li>Input</li><li>White Paint</li></ul> <p><strong>Aerial Specifications:</strong></p><p>Terex Hi-Ranger Optima TC55 Insulated Non-Overcenter Aerial Device<br>Providing A Working Height Of 6�.0 Ft �nd A Side_ Reach Of 42_.8 Ft. . . . .<br>A Self Locking Worm Gear Rotation Drive Is Provided And Equipped With A B1-D1rectmnal Motor.<br>Continuous & Unrestricted Rotation<br>Boom w/116 Degree Lower Boo� Articulation �o Ground Access In �h� Non-Overce�ter Position<br>Lower Boom: Filament Wound High Strength Fiberglass lnser_t �rov1drng An Insulation �ap.<br>Upper Boom: Filament Wound Taper�d Fiberglass Boom Pr_ov1d1_ng A Clear_Span Insulation Gap.<br>Upper Boom Rest With A Cam Type Tie Down Strap. Boom Tip With Hydraulic Platform Rotator.<br>Upper Controls: “Control-Plus” Sin9le Stick Con_troller. .<br>Platform Leveling Control, Hydraulic Platform Tilt Is Provided At P�atform And Lower Controls.<br>Engine Stop/Start Controlled At Platform �nd Lower Controls. Engine Throttle_ “.-dvance<br>Dual Hydraulic Tool Outlets At Platform With F�ow Contr�lLower Controls: lnd1v1dual Control<br>Levers Are Provided And Located In An Accessible Location On The Turntable.<br>An Upper/Lower Control Selector Provides Over�ide Of Platform Con�rols.<br>Aerial Device Is Designed As A Category B Machine In Accordance With ANSI/SIA A92.2-2015.<br>The Upper And Lower Boom Will Be Articulated Independently.<br>Terex South Dakota Inc. Can Only Test Up To 69kv When This Option Is Ordered. Can Be Rated<br>From 46KV Up To 69KV Per ANSI/SIA A92.2-2015 Depending On: Model, Options And Fiberglass<br>Length – Must Specify KV Rating When Ordering.<br>Demand Throttle Disable<br>Side Mounted Fiberglass Platform 24″ X 48″ X 42″: [Curbside] 700 Lbs. Rated Platform Capacity.<br>Insulated Platform Liner For 24″ X 48″ X 42″ Platform<br>Vinyl Platform And Control Cover For 24″ X 48″ Plat�orm .</p>

<p>VST40MHI on Ford F550 4x4</p><p>We are pleased to quote the <strong>VERSALIFT VST-40-MHI</strong>, insulated 40 ft. 4 in. (12.3 m) telescopic aerial platform lift, 45 ft. 4 in. (13.8 m) working height, 30 ft. 2 in. (9.2 m) horizontal reach including the following items (based on a 40” frame height):</p><p><strong>ARIAL LIFT SPECIFICATIONS:</strong><br> </p><p><strong>PLATFORM </strong>– The closed fiberglass platform is 24 In. x 30 In. x 42 In. deep (.61 m x .76 m x 1.07 m) with an inside and outside step for easy access. The platform capacity is 400 lbs. (181 kg) with the jib and winch installed and 500 lbs. (227 kg) with the jib and winch removed. The platform is equipped with a tubular rubber rest/support. </p><p><strong>PLATFORM LINER AND VINYL COVER </strong>– A 50 kV rated liner and soft vinyl cover are supplied for the platform.  </p><p><strong>PERSONNEL RESTRAINT SYSTEM </strong>– An Arc flash rated safety harness and lanyard are supplied. The anchor for the lanyard is attached to the platform support.</p><p><strong>SINGLE STICK UPPER CONTROL </strong>– The full pressure single-stick upper control includes a safety trigger to prevent inadvertent operation. The lift movements correspond with control handle movements. An emergency stop and a tool selector control are located at the upper controls.</p><p><strong>TRUGUARD™ 2.0 </strong>– This advance upper controls isolation system provides 4″ of electrical isolation from the entire upper controls, including the control dash panel. This system also includes a protective shield which helps prevent environmental and work-related contaminants from making direct contact with the isolating surfaces.  </p><p><strong>HYDRAULIC PLATFORM ROTATION </strong>– A hydraulic rotary actuator, operated by a control lever, rotates the platform 180° from one side of the boom, to the end-hung position, and to the other side of the boom.  </p><p><strong>HYDRAULIC PLATFORM LEVELING </strong>– A master and slave cylinder controls platform leveling. The leveling system can be operated from the upper or lower controls to adjust platform leveling, tilt the platform for clean out, or to ease the removal of an injured operator.</p><p><strong>HYDRAULIC TOOL CIRCUIT AT THE PLATFORM </strong>– This system is intended for open center hydraulic tools. The tool circuit provides 6 gpm (22.7 lpm). A pressure reducing valve in the tool circuit limits the tool pressure. The valve can be adjusted from 1000 to 2500 psi (70 to 175 kg/cm2). Includes quick disconnect fittings.</p><p><strong>LINE-LIFTING SOCKET </strong>– Built as part of the platform support structure, is a vertical line-lifting socket for 3 in. (76 mm) diameter line-lifting attachments. The socket is automatically leveled with the platform without any manual adjustments.</p><p>Call for more Info.</p><p> </p><p> </p>

<strong>VANTEL 29 – FORD TRANSIT</strong>

<p><strong>CHASSIS SPECIFICATIONS:</strong></p><p><strong>Minimum Chassis Requirements:</strong></p><ul><li>Clean Cab to Axle Dimension (tops, sides & bottoms) ………………………………………………………. 84 in. (2.14 m)</li><li>Frame Resisting Bending Moment ……………………………………………………………… 530,000 in-lbs. (60,000 N-m)</li><li>GVWR ………………………………………………………………………………………………………………. 19,500 lbs. (8845 kg)</li><li>Front GAWR ………………………………………………………………………………………………………… 7,000 lbs. (3175 kg)</li><li>Rear GAWR ………………………………………………………………………………………………………. 13,500 lbs. (6120 kg)</li><li>Approximate Curb Weight for Stability …………………………………………………………………… 14,500 lbs. (6580 kg)</li><li>PTO Provision</li><li>Rear Fuel Tank Only</li><li>Trailer brake controller</li><li>Rear view camera and prep kit</li><li>Ford F-550 4×4</li><li>Diesel Engine</li></ul><p><strong>BODY SPECIFICATIONS</strong></p><p><strong>Steel Service Body:</strong></p><p>132″ Service Body 48 SS / 40 CS inches high X 94 inches wide.</p><p><strong>Body Dimensions:</strong></p><ul><li>20 Inch compartment depth.</li><li>54 Inch bed area.</li><li>32 SS / 24 CS Inch top of floor to top of body.</li><li>26 SS / 18 CS Inch horizontal compartment height.</li></ul><p>VST-47-MHI VSW-23391 VERSALIFT.COM Page 4 of 6 August 25, 2022</p><p><strong>BODY SPECIFICATIONS (Continued) Body Materials:</strong></p><ul><li>16 Ga. Galvanneal body materials.</li><li>12 Ga. Hot rolled treadplate floor.</li><li>12 Ga. Hot rolled treadplate compartment tops.</li></ul><p><strong>Door Details:</strong></p><ul><li>Stainless Steel Automotive rotary type door latches</li><li>Latch Covers on All doors.</li><li>Stainless steel rod and socket type door hinges.</li><li>Chain stops on all doors.</li><li>18 Ga. Double Panel Body Doors.</li></ul><p><strong>Body Features:</strong></p><ul><li>Rubber rolled crown type fenders.</li><li>Master door lock system.</li><li>Front bulkhead.</li><li>Shelving / Hooks installed on DUAL Uni-Strut for infinite adjustment.</li><li>Two (2) formed angle Mudflap brackets</li></ul>

<p><strong>CHASSIS SPECIFICATIONS</strong></p><p><strong>Minimum Chassis Requirements:</strong></p><ul><li>Clean Cab to Axle Dimension (tops, sides & bottoms) ………………………………………………………. 84 in. (2.14 m)</li><li>Frame Resisting Bending Moment ……………………………………………………………… 530,000 in-lbs. (60,000 N-m)</li><li>GVWR ………………………………………………………………………………………………………………. 19,500 lbs. (8845 kg)</li><li>Front GAWR ………………………………………………………………………………………………………… 7,000 lbs. (3175 kg)</li><li>Rear GAWR ………………………………………………………………………………………………………. 13,500 lbs. (6120 kg)</li><li>Approximate Curb Weight for Stability …………………………………………………………………… 14,500 lbs. (6580 kg)</li><li>PTO Provision</li><li>Rear Fuel Tank Only</li><li>Trailer brake controller</li><li>Rear view camera and prep kit</li><li>Chevy 5500 4×4</li><li>Diesel Engine</li></ul><p> </p><p><strong>BODY SPECIFICATIONS</strong></p><p><strong>Steel Service Body:</strong></p><p>132″ Service Body 40 inches high X 94 inches wide.</p><p><strong>Body Dimensions:</strong></p><ul><li>20 Inch compartment depth.</li><li>54 Inch bed area.</li><li>24 Inch top of floor to top of body.</li><li>18 Inch horizontal compartment height.</li></ul><p><strong>Body Materials:</strong></p><ul><li>16 Ga. Galvanneal body materials.</li><li>12 Ga. Hot rolled treadplate floor.</li><li>12 Ga. Hot rolled treadplate compartment tops.</li></ul><p><strong>Door Details:</strong></p><ul><li>Stainless Steel Automotive rotary type door latches</li><li>Latch Covers on All doors.</li></ul><p>VST-40-MHI VSW-23390 VERSALIFT.COM Page 4 of 6 August 25, 2022</p><p><strong>BODY SPECIFICATIONS (Continued)</strong></p><ul><li>Stainless steel rod and socket type door hinges.</li><li>Chain stops on all doors.</li><li>18 Ga. Double Panel Body Doors.</li></ul><p><strong>Body Features:</strong></p><ul><li>Rubber rolled crown type fenders.</li><li>Master door lock system.</li><li>Automotive Bulb Type Weatherstripping.</li><li>Front bulkhead.</li><li>Shelving / Hooks installed on DUAL Uni-Strut for infinite adjustment.</li><li>Two (2) formed angle Mudflap brackets</li></ul><p><strong>Streetside Compartmentation:</strong></p><p><strong>1st Vertical:</strong></p><ul><li>28 Inches wide Two (2) shelves each with adjustable dividers on 4″ centers.</li></ul><p><strong>2nd Vertical:</strong></p><ul><li>28 Inches wide Two (2) shelves each with adjustable dividers on 4″ centers.</li></ul>

<p><strong>CHASSIS SPECIFICATIONS Minimum Chassis Requirements:</strong></p><ul><li>Clean Cab to Axle Dimension (tops, sides & bottoms) …………………………………………………….. 108 in. (2.74 m)</li><li>Frame Resisting Bending Moment ……………………………………………………………… 360,000 in-lbs. (41,000 N-m)</li><li>GVWR ………………………………………………………………………………………………………………. 22,500 lbs. (8845 kg)</li><li>Front GAWR ………………………………………………………………………………………………………… 7,000 lbs. (3175 kg)</li><li>Rear GAWR ………………………………………………………………………………………………………. 13,500 lbs. (6120 kg)</li><li>Approximate Curb Weight for Stability …………………………………………………………………… 14,500 lbs. (6580 kg)</li><li>PTO Provision</li><li>Rear Fuel Tank Only</li><li>Chevy 6500 4×4</li><li>Diesel Engine</li><li>Back up Camera</li><li>Automatic Transmission</li><li>Dash mounted upfitter switches</li></ul> BODY SPECIFICATIONS <p><strong>Steel Service Body:</strong></p><p>150″ Service Body 48 SS / 40 CS inches high X 94 inches wide.</p><p><strong>Body Dimensions:</strong></p><ul><li>20 Inch compartment depth.</li><li>54 Inch bed area.</li><li>32 SS / 24 CS Inch top of floor to top of body.</li><li> </li></ul><p>26 SS / 18 CS Inch horizontal compartment height.</p><p><strong>BODY SPECIFICATIONS (Continued)</strong></p><p><strong>Body Materials:</strong></p><ul><li>16 Ga. Galvanneal body materials.</li><li>12 Ga. Hot rolled treadplate floor.</li><li>12 Ga. Hot rolled treadplate compartment tops.</li></ul><p><strong>Door Details:</strong></p><ul><li>Stainless Steel Automotive rotary type door latches</li><li>Latch Covers on All doors.</li><li>Stainless steel rod and socket type door hinges.</li><li>Chain stops on all doors.</li><li>18 Ga. Double Panel Body Doors.</li></ul><p><strong>Body Features:</strong></p><ul><li>Rubber rolled crown type fenders.</li><li>Master door lock system.</li><li>Front bulkhead.</li><li>Shelving / Hooks installed on DUAL Uni-Strut for infinite adjustment.</li><li>Two (2) formed angle Mudflap brackets</li></ul><p><strong>Streetside Compartmentation:  (48″ High) 1st Vertical:</strong></p><ul><li>24 Inches wide with Two (2) shelves each with adjustable dividers on 4″ centers.</li></ul><p><strong>2nd Vertical:</strong></p><ul><li>24 Inches wide with Two (2) shelves each with adjustable dividers on 4″ centers.</li></ul>